Loctite
Low Strength/Small Screw Ideal for fastener diameters of 1/4" and smaller. Controlled lubricity for accurate clamp loads. Parts can be separated using hand tools
Medium Strength A general purpose removable threadlocker for fasteners between 1/4" and 3/4" diameters. Controlled lubricity for accurate clamp loads. Parts can be separated using hand tools
Medium Strength/High Temperature This threadlocker resists oil and mild surface contamination at continuous temperatures to 450™. Suitable for fasteners between 1/4" and 3/4" diameters
Medium to High Strength A permanent threadlocker for fasteners up to 3/4" in diameter. High lubrication for easy assembly. Excellent for preventing rust and corrosion in extreme chemical/environmental conditions
High Temp/High Strength Provides a fast cure on most surfaces. Including "as received" fasteners. Heat and hand tools are required for disassembly
High Strength Protects threads from rust and corrosion. Removable with heat and hard tools
Wicking Grade A medium strength threadlocker for pre-assembled bolts up to 1/2". Secures set screws and other assemblies after settings are completed. Protects threads from rust and corrosion. Penetrates threads by capillary action. Seals welds and porous metal parts
Toughened The original elastomer-modified instant adhesive. Excellent peel impact and shear strength
Surface Insensitive A general purpose adhesive for difficult-to-bond surfaces
General Purpose Gel A high viscosity general purpose instant adhesive. Gel formulation will not run off vertical surfaces
Clear/Toughened An adhesive formulated for excellent impact and peel strength in gap filling applications
Plastic Bonder A medium viscosity instant adhesive for bonding plastics
A general industrial-grade instant adhesive. Excellent choice for bonding close fitting metal parts
Surface Insensitive Gel Bonds dissimilar parts. Can be applied to vertical surfaces. Excellent for almost all surfaces. Ideal for porous substrates and rough and acidic surfaces
Designed to bond rubber metal and plastic parts with gaps to .004"
High Temperature A high temperature sealant specially engineered for making or dressing gaskets in rigid assemblies. Fills gaps and permits clamping loads to be maintained for strong leakproof assemblies
Makes flexible gaskets for rigid machined flanges with less than .050" gap. Flexes with flanges that move in service
Hydraulic/Pneumatic Fittings A liquid sealant for locking and sealing high pressure fluid power systems with tapered fittings. Contains no fillers and will not foul valves or fluid filtering systems
Controlled Strength A general purpose instant sealant for tapered and straight/tapered fittings. Controlled strength for ease of diassembly
Hydraulic Sealant A high strength hydraulic sealant that contains no fillers or particles
Heavy Body RTV Silicone Superior flexibility and adhesion. Provides instant seal. Non-corrosive low odor and low volatility
High Performance RTV Silicone Gasket Maker High performance for rigid flange assemblies. Low volatility
Slow Cure Locks and seals threaded fittings. Parts may be repositioned up to 24 hours after application
General Purpose A low viscosity retaining compound that bonds rigid metal assemblies. Easily joins dissimilar metals
High Temperature A high viscosity liquid retaining compound. Locks and secures metal cylindrical assemblies up to .015" diameter clearance. Prevents metal fretting and corrosion. Seals against leakage
Maximum Strength For use where high dynamic force or cyclic loading is expected. Locks cylindrical assemblies up to .010" diameter clearance
A creamy non-running adhesive/sealant. Repairs worn machine parts. Restores correct fit to mating assemblies
A solvent-based primer that speeds the cure of all Loctite® brand anaerobic adhesives and ensures proper cure on inactive metals. Has on-part life of 7 days and dries in 30 - 70 seconds
A solvent-based primer that features very long on-part life of 30 days. Use to speed the cure of all Loctite® brand anaerobic products and ensure proper cure on inactive metals. Ideal for cure conditions below room temperature. Dries in 30 - 70 seconds
AA 330™ General purpose. Good impact resistance. Ideal for bonding dissimilar substrates like PVC, phenolic, and acrylic compounds. Medium to high viscosity. Activator required, Loctite® SF 7387, sold separately.
Exclusive formula suspends copper and graphite in a high quality grease. Protects metal parts from rust corrosion galling and seizing
Removes gaskets from any type of assembly in 10 to 15 minutes. Prepares metal parts for new gaskets eliminating scraping and sanding. Works on wood non-corrosive on aluminum. Not for use on plastics linoleum or synthetic fibers
Standard abrasive paste for fast metal removal. Produces a smooth flat surface but not a polished one. Leaves a rust preventing film on lapped surfaces. Uses include lapping and honing and grinding activities for valve seats gear teeth dowel holes in dies bushings and more
Tough Rubber Coating Inhibits rust and corrosion seals insulates and identifies almost any material in minutes. Creates a non-slip gripping surface. Rubber coating won't crack or chip. Dip spray or brush to apply. Now toluene free. Last for years
Provides a moisture-proof barrier that lubricates and protects electrical equipment from salt dirt and corrosion. High dielectric strength. Good thermal oxidation and chemical stability
Mixer Cup Pre-measured. Fills porosities and can be used to build up worn parts https://www.arksafety.com/sites/default/files/442-21425.eps.jpg
Cut off a section knead and apply to leaking pipes or damaged equipment. Certified and approved for use with drinking water system components
This putty like material is ideal for plumbing irrigation and marine applications because it is unaffected by chlorinated or salt water. Hand kneadable
Metal-free. Excellent lubricity. Provides outstanding lubrication to all metals including stainless steel aluminum and soft metals
Forms tough flexible gaskets directly on the flange. Offers excellent adhesion to oily surfaces. Low odor non-corrosive and low volatility
Formulated to protect assemblies exposed directly or indirectly to fresh and salt water. Works especially well in high humidity conditions. It has excellent lubricity superior water wash-out and water spray resistance and prevents galvanic corrosion
Lubricates and protects Class 1 2 and 3 power plant hardware. Recommended for highly corrosive environments
Metal Free Metal-free formulation provides high levels of purity and excellent lubricating properties. For Class 1 2 and 3 power plant hardware
Copper-free. For preventing corrosion seizing galling in harsh chemical environments and temperatures
A non-aqueous hydrocarbon-based solvent designed for cleaning and degreasing surfaces to be bonded with adhesives as well as for general purpose industrial cleaning. Will not cause flash rusting on water sensitive parts. Drying time is 5-20 minutes (without wipe) and 1-2 minutes (with wipe). Contains no ozone depleting compounds
Removes grease, lubricants, cutting oils, fuel oils, road salt, tar, light carbon, food stains, wax, animal fats, mildew, and soot.
Reliable paste-like gasket sealant/dressing/coating. Sets quickly to a hard set and is recommended for rigid permanent assemblies
Reliable paste-like gasket sealant/dressing/coating. Sets more slowly to a pliable film best suited for non-rigid vibrating assemblies
SF 754™ One-step rust treatment goes on white and converts rust to a durable, black, metal-protective coating in 10 minutes. Wire brush parts and apply with brush or spray. Surface rust must be present. Use as a primer or finish coat. Resists temperatures to 250º F intermittent, 200º F continuous. Known as Extend® Rust Treatment.
SF 7840™ Biodegradable cleaner degreaser contains no hazardous solvents and dilutes with water to meet a wide range of industrial cleaning applications.
Multi-purpose lubricant stops sticking friction squeaking and binding of moving parts. Will not mar paint rubber or plastic surfaces. Waterproofs and electrically insulates. Non-gumming
Heavy duty temperature resistant petroleum-based lubricant compound fortified with graphite and metallic flake. Inert will not evaporate or harden in extreme cold or heat
Silicone Adhesive Sealants Makes gaskets that resist temperatures to 600™ intermittent. Resists aging weather and thermal cycling without shrinking cracking or hardening
Silicone Adhesive Sealants Cures to a tough flexible rubber. Makes reliable "formed-in-place" gaskets that resist shrinking cracking and migrating. Coats pre-cut gaskets to increase reliability. Low volatility
Convenient: small enough to be pocket friendly. No leaks drips or spills . Keeps tool boxes work benches and hands clean. Fast and easy-to-apply. Solid formula: great for overhead use. Functional for a full range of uses. A heavy duty temperature-resistant lubricant fortified with graphite and metallic flake. Will not evaporate or harden in extreme cold or heat for assemblies up to 1600™